为满足安装精度和下水节点要求，需进一步提高舰载导弹垂直发射装置安装精度和效率，缩短安装周期，降低测量限制条件。而快速、精确的进行装配前后的精度测量成为制约发射装置安装调试的关键所在。舰载导弹垂直发射装置在水面舰船上的安装和测量技术是水面舰船建造过程中的一项重要技术，决定了导弹垂直发射装置安装后的最终精度。本文介绍了国内外舰载导弹垂直发射装置精度的测量方法及发展现状，并指出了国内舰载导弹发射装置精度测量方面存在的问题及努力方向。
To meet the requirement of installation accuracy and boat launching node, it calls for improving the installation accuracy and efficiency of shipborne vertical laucher equipment of missile, aiming to shouten the installation period and reduce the measure restrictive condition. Rapid and accurate precision measure before and after assembly mostly restricts the installation and adjustment of the equipment. The installation and measure technique of shipborne vertical laucher equipment of missile is an extremely important one which determins the final accuracy of vertical laucher equipment of missile after installation. This article intrduce the measure method and current development status of the domestic shipborne vertical laucher equipment of missile and the abroad.Problem and future direction are presented about the domestic equipment in precision measure.
2018,40(12): 129-132 收稿日期：2018-08-20
DOI：10.3404/j.issn.1672-7649.2018.12.026
分类号：TJ06
基金项目：国防基础科研计划项目
作者简介：何朝勋(1976-),男,硕士,研究员,从事导弹发射装置研究
参考文献：
[1] 李敬堂, 王基恩编著. 舰载导弹发射装置结构与设计[M]. 哈尔滨:哈尔滨工程大学出版社, 2006.
[2] LO S, CHIU J, LIN H. Rapid measurement of surface roughness for face-milling aluminum using laser scattering and the Taguchi method[J]. The International Journal of Advanced Manufacturing Technology, 2005, 26(9-10):1071-1077
[3] MOLLEDA J, J M, MOLLEDA J, et al. On-line flatness measurement in the steelmaking industry[J]. Sensors (Basel), 2013(8):10245-10272
[4] BABU G D, BABU K S, GOWD B U M. Evaluation of surface roughness using machine vision[C].//Emerging Trends in Robotics and Communication Technologies (INTERACT), 2010 International Conference on. IEEE, 2010:220-223.
[5] 王雷. 激光平面度测量系统光斑位置检测技术的研究[D]. 大连:大连海事大学硕士学位论文, 2009.
[6] VANNONI M, MOLESINI G Paired interferometric measurement of planarity and parallelism[C]. Optical Metrology[J]. International Society for Optics and Photonics, 2003:864-871
[7] VANNONI M, BERTOZZI R. Parallelism error characterization with mechanical and interferometric methods[J]. Optics and lasers in engineering, 2007, 45(6):719-722
[8] JOSHI D, KUMAR A, KUMAR Y, et al. Evaluation of parallelism by ultrasonic echo method[J]. Applied Acoustics, 2010, 71(5):446-450
[9] SONG Y, HAO Q, LI D. Measurement of parallelism and perpendicularity of large-size workpieces laser alignment method[C]//2nd International Symposium on Advanced Optical Manufacturing and Testing Technologies. International Society for Optics and Photonics, 2006:61502H-61502H-5.
[10] 耿晨刚. 导轨精度检测方法[J]. 中州大学学报, 2013, 10, 30(5):122-125
[11] 邵兵, 赵建波, 吴福强, 等. 动基座条件下垂直发射装置状态参数检测方法[J]. 火力与指挥控制, 2012, 5, 37(5):191-194
[12] 邵兵, 刘志伟, 何阳. 基于动基座条件下的筒弹定位导轨精度测量方法[J]. 宇航计测技术, 2015, 2, 35(1):66-70
