在开发系统程序时，经常发现相间换热系数过大导致程序计算两相流动时出现物性错误，从而导致计算失败。因此采用RELAP5使用的相间换热系数限制关系式对相间换热系数进行限制，采用水平环形雾状流、垂直环形雾状流2种工况进行计算，计算结果表明，单纯的采用RELAP5使用的相间换热系数限制关系式并不能使计算稳定，必须减小该相间换热系数限制关系式的最大值才能使得计算稳定。同时，不同空泡份额下能够稳定计算两相流动的相间换热系数最大值限制不相同，且相间换热系数值的大小对空泡份额的计算有很大影响。
When the in-house two-phase system analysis code is developed, it is usually found that the fluid property error occurs during the computation of two-phase flow due to the too large interfacial heat transfer coefficient, and the computation fails. Therefore, the interfacial heat transfer coefficient limit correlation used in RELAP5 is applied in our in-house code, and the horizontal and vertical annular mist flow are computed, the computation results show that the only application of interfacial heat transfer coefficient limit correlation used in RELAP5 can't stabilize the computation and decreasing the maximum limitation of the interfacial heat transfer coefficient limit correlation can stabilize the computation. Meanwhile, the maximum limitation of the interfacial heat transfer coefficient is different for two-phase flow computation with different void fraction, and the effect of the value of interfacial heat transfer coefficient on the void fraction is great.
2021,43(4): 135-140 收稿日期：2019-09-09
DOI：10.3404/j.issn.1672-7649.2021.04.027
分类号：TL383
基金项目：国家科技重大专项资助项目(2017ZX06002002)
作者简介：陈玉昇(1989-),男,博士研究生,主要研究方向为核动力装置控制运行与故障诊断
参考文献：
[1] 俞冀阳, 贾宝山.反应堆热工水力学[M]. 北京: 清华大学出版社, 2011, 131−134.
[2] 冯可新, 彭敏俊, 徐宇翔. 核电站给水加热器建模仿真[J]. 原子能科学技术, 2014, (2): 310-317
FENG Ke-xin, PENG Min-jun, XU Yu-xiang. Nuclear power plant feedwater heater modeling and simulation[J]. Atomic Energy Science and Technology, 2014, (2): 310-317
[3] 章旋, 茆荣, 曹建亭. 核电站全范围模拟机关键技术探讨[J]. 热力发电, 2011, 40(1): 16-18
ZHANG Xuan, MAO Rong, CAO Jian-ting. Discussion on key technology of full range simulator in nuclear power plant[J]. Thermal Power Generation, 2011, 40(1): 16-18
[4] 林萌, 等. RELAP5作为核电站模拟器热工水力系统程序的改造[J]. 核动力工程, 2005, (2): 125-129
LIN Meng, et al. RELAP5 as a nuclear power plant simulator thermal hydraulic system program transformation[J]. Nuclear Power Engineering, 2005, (2): 125-129
[5] 李美琳, 林萌, 杨燕华, 等. 应用于反应堆热工水力程序的核态沸腾传热关系式评价[J]. 核科学与工程, 2015, (1): 36-42
LI Mei-lin, LIN Meng, YANG Yan-hua, et al. Evaluation of the relationship of nuclear state boiling heat transfer for reactor thermal hydraulic procedures[J]. Nuclear Science and Engineering, 2015, (1): 36-42
[6] LI, Y., M. LIN and Y. YANG Coupling methods for parallel running RELAPSim codes in nuclear power plant simulation[J]. Nuclear Engineering and Design, 2016, (297): 1-14
[7] Nuclear Safety Analysis Division. RELAP5/MOD3.3 code manual volume I : Code structure, system models, and solution methods[M].US : Nuclear Regulatory Commission, 2001: 98−105.
[8] The RELAP5 Code Development Team. RELAP5/MOD3 Code Manual[R]. NUREG/CR-5535-V1.1995: 213−215
