以No.37+Ka4-70导管螺旋桨为基础进行三维实体建模，利用计算流体力学方法对ROV导管螺旋桨模型进行敞水数值模拟，得到导管螺旋桨的推力、扭矩，并与相应图谱数据对比，证明文章数值方法的有效性。在此基础上进一步对几种平导管螺旋桨进行数值模拟和对比分析，结果表明推力损失在10%左右，在低成本ROV情况下为平导管推进器选用提供参考依据。
The 3D model of ROV thruster for #37 duct and Ka4-70 propeller was built with the common design software system in the article, their open water hydrodynamics performance was simulated by CFD software. Comparisons and analysis of thrust force and torque to the propeller chart results show that the numerical method is effective. Based on this, several flat ducted propellers were calculated and analyzed, the decrease of flat ducted propellers is about 10%, so as to provide application reference for the ROV thruster under low cost .
2022,44(21): 88-91 收稿日期：2021-07-22
DOI：10.3404/j.issn.1672-7649.2022.21.018
分类号：U664.34
基金项目：国家重点研发计划项目（2018YFC0309700）；国家自然科学基金资助项目（51709137）
作者简介：刘可峰(1978-),男,讲师,研究方向为船艇与潜器研发、CFD应用研究
参考文献：
[1] 柯力, 刘可峰, 李家旺, 等. 变重心潜器操控性能[J]. 造船技术, 2017, 339(5): 33–36
[2] 夏添, 刘可峰, 郭乔, 等. 基于FDM的船舶模型强度实验[J]. 工程塑料应用, 2019, 47(9): 121–126
[3] ABOLFAZL A, URBAN S, RICKARD E. Bensow. Numerical and experimental analysis of cavitation inception behaviour for high-skewed low-noise propellers[J]. Applied Ocean Research, 2018, 79(4): 197–214
[4] 王超, 韩康, 孙聪, 等. 船用螺旋桨优化设计与参数分析[J]. 华中科技大学学报(自然科学版), 2020, 48(4): 1–8
[5] EHSAN J, EHSAN Y, JAVAD A M. Numerical investigation on the effect of shaft inclination angle on hydrodynamic characteristics of a surface-piercing propeller[J]. Applied Ocean Research, 2020, 98(1): 2–16
[6] 王树齐, 张亮, 徐刚, 等. 自由面条件下水平轴潮流能叶轮水动力研究[J]. 哈尔滨工程大学学报, 2016, 37(10): 1330–1334
[7] BRENDEN P E, BERNARD T R, RICHARD B M, et al. A viscous vortex lattice method for analysis of cross-flow propellers and turbines[J]. Renewable Energy, 2019, 143: 1035–1052
[8] MAJDFAR S, GHASSEMI H, FOROUZAN H, et al. Hydrodynamic prediction of the ducted propeller by CFD solver[J]. Journal of Marine Science and Technology, 2017, 25(3): 268–275
[9] 胡健, 王楠, 胡洋. 导管桨水动力特性的数值研究[J]. 哈尔滨工程大学学报, 2017, 38(6): 815–821
[10] 赵威, 刘敏, 彭旭, 等. 前置定子叶片周向弯曲对导管桨非定常特性的影响[J]. 中国造船, 2018, 226(2): 24–32
[11] 吴家鸣, 廖贯宇, 赖宇锋, 等. 导管剖面设计对导管螺旋桨水动力特性的影响[J]. 舰船科学技术, 2017, 39(11): 38–43
[12] 刘勇杰, 徐青, 胡勇, 等. 基于CATIA的船用螺旋桨三维建模方法[J]. 船海工程, 2018, 47(4): 84–87
